Ji Routing b70 has a password after mining

『One』Can the B70 be able to withdraw coins?

No, it hasn’t started yet
Today, the official Weibo officially responded: “Upgrade mining for 200W old users. The time has not yet been determined, and the official announcement of Jiluo will be released to tell everyone, including the open model, etc. I hope Jimi will not believe or spread rumors, pay more attention to Jilu’s official blog, don’t be impatient, don’t rush.”
In other words, the official deployment is still underway, and there is still some time before the official launch, but it will not be too long.
Previously, Ji Routing CEO Wang Chuyun disclosed in an open letter that the existing Ji Routing will be open for application in January and gradually open to the entire network. As for the X-X blockchain router that sells for 1,024 yuan, the official sale will start in March.

『紴』 Is the pole route B70 the same as the pole route 4 enhanced version?

Compared with the pole 4, except for the antenna and the fuselage color, other places are the same. it’s the same.

The specific parameters are as follows:

CPU: MT7621 dual-core 880Mhz

Memory: 256M

Flash memory: 128M

Wireless rate: 2.4G 300M / 5G 867M

Wired: 1WAN+3LAN full Gigabit Ethernet port

Number of antennas: 4

Antenna gain : 5dBi

USB interface: one for each of 2.0&3.0

(2) There is a password after mining with pole routing b70 Extended reading:

Methods to enhance the signal:

1. Find a perfect place to place the router at home to achieve the best layout

Try to install the router as close to the middle of the home as possible to improve wifi signal, this is a “rule of thumb”: the average wireless router has a signal range of less than 50 meters indoors and less than 100 meters outdoors.

2. Find electronic equipment that may cause signal interference

The wireless signal may be weakened by the interference of other electrical equipment. All of the following devices may interfere with the wireless wifi signal: refrigerators, TVs, microwave ovens, power cords, remote controls, wireless audio equipment (speakers, microphones), monitors, monitors, wireless cameras, mobile phone Bluetooth, satellite TV receivers, and more.

3. Change the appropriate wifi signal channel

If you live in an apartment or a densely populated building, wireless interference may come from your neighbor’s WiFi router. The exact source of the interference is hard to pin down, but with any wireless device smartphone or tablet, some software can detect how many wireless devices are within range.

How to reset the B70 of the “three” pole router

1. You can restore the router to factory settings first. There is a small hole on the back of the router, which is generally written as RST or RESET. Small and sharp things such as toothpicks or pen nibs can restore the factory settings of the router by poking the hole for more than 5 seconds when the router is powered on; The general connection and setting methods for network sharing equipment are as follows: connect the network cable from the broadband modem to the WAN port of the router, connect each computer to the LAN port of the router, and set the IP address of the computer network card to obtain automatically. Enter 192.168.1.1 in the address bar (some are 192.168.0.1, you need to check the network parameters obtained by your computer’s network card, and log in through the IP address of the gateway) to log in to the router. Generally, the user name and password are both admin, select WAN port settings, and set your Set the broadband account and password to PPPOE mode (if it is a fixed IP, choose static IP mode), save it and restart it.

『4』 Can the expansion disk be used for the B70 of the extreme router?

It can be used, but the risk owner has considered it by himself.

It is generally not recommended to mine with expansion disks, and may be banned. Many people’s accounts have been banned.

『Wu』 How to enter the background of the B70 with the pole route

There are two ways to enter the background of the pole route,

In the case of the pole route connected, open the browser The router can enter 192.168.199.1 in the address bar to enter the pole routing background. Before entering, you need to enter the router background password, the default password is admin. If you don’t want your router background to be changed casually, it’s better to change it to a more secure password.

『Lu』 How to withdraw ACT GCT of Extreme Routing Mining

Complete Tutorial of Extreme Routing ACT&GCT withdrawal

Main process:

STEP1: Withdraw GCT to BigONE

STEP2: Swap GCT into ACT

STEP3: Withdraw ACT to Huobi

STEP4 : Huobi ACT exchanged for BTC or ETH or USDT

STEP5: BTC or ETH or USDT exchanged for RMB

step1 GCT withdrawal to BigONE

download wallet

The third-party chain wallet can be downloaded in the Jirouting APP—Routing Tool—JiChain Internal Beta

Currently only supports Android phones, IOS is under development

『柒』 GTC0.00298

It is equipped with larger memory capacity, faster network speed, and more mining. Now the new product X is on the market, you may wish to pay attention.

『渌』Note.��After the mining APP is successful, can you check the password during registration in the background?

『玖』How to set the 5G signal is too weak after the B70 is a veteran of the extreme router?

Hello, I seem to have encountered your problem before. The following is my original solution and method. I hope it can help you. If there are any mistakes, please forgive me! 1. You can restore the router to factory settings first. There is a small hole on the back of the router, which is generally written as RST or RESET. Find something small and sharp, such as a toothpick or pen tip, and poke the hole for more than 5 seconds when the router is powered on. You can restore the factory settings of the router; 2. Re-set the relevant network parameters of the router: The router is a device that forms a local area network to achieve network sharing. The general connection and setting methods are as follows: Connect the network cable from the broadband modem to the WAN port of the router, each The computer is connected to the LAN port of the router, the IP address of the computer network card is set to obtain automatically, enter 192.168.1.1 in the address bar of the computer browser (some are 192.168.0.1, specifically to check the network parameters obtained by your computer network card, through the IP address of the gateway Address to log in) log in to the router, generally the user name and password are admin, select WAN port settings, set your broadband account and password to PPPOE mode (if it is a fixed IP, choose static IP mode), save and restart. , thank you very much for your patience to watch, if you help, please adopt it, I wish you a happy life! Thanks!

0

Related Ad

Comments (No)

Leave a Reply